Husqvarna chain file

When properly aligned, you basically just push it straight across the center of both rollers on the gauge. Just sharpen every tooth on the chain that has the same cutting direction, which is every other tooth since they alternate back and forth. When using the guide, I've found it's easiest to hold the guide with one hand and use your other hand to work the file. When you have all of the teeth sharpened on one side, flip your saw around and orientate the gauge to the teeth on the other side.

After you get familiar with the guide, it only takes about 10 minutes to completely sharpen a chain. You can push the round file through the holes to keep the kit all together so you don't loose the guide. Just remember to orientate the guide to the proper angle and use a steady pushing motion with the round file.

After a while, the round file will become worn out, so if you don't feel like you're getting a good bite on the chain, it may be time to replace the file. The kit comes with two round files so you'll get a lot of use out of the kit before you have to buy another file. These sawbuck assembly instructions create an easy way for anyone to build a strong and durable folding rack for cutting firewood.

Lock the chain brake to fix the chain position. Straddle the Husqvarna chain file gauge over the chain with the arrows pointing toward the end of the cutting bar. File each tooth on the opposite side. Make several passes until you reveal bare metal and the tooth feels sharp to the touch. Unlock the brake and slide the chain to access the rest of the teeth pairs as needed.

Fit the depth gauge -- built into the file gauge -- over the chain teeth. The depth gauge has a separate slot, depending on whether you regularly cut hard or soft wood. Select the proper slot and place it over the cutting tooth. Fit the U-shaped groove of the depth gauge around the tooth set in front of the set you wish to file so the gauge is locked in position.

Push the flat file forward across the cutting tooth to file the tooth down to the correct depth. Stop filing when the flat file makes contact with the depth gauge's flat metal plate. Repeat with the remaining sets of cutting teeth on the chain. This step is only required every third or fourth time you sharpen the chain.

A former cake decorator and competitive horticulturist, Amelia Allonsy is most at home in the kitchen or with her hands in the dirt. The main types of files are the 4mm, 4.

These files can either flat files or round files depending on the cutter you are sharpening. If you have a chain with a chipper cutter, you will go for a round file. If the cutter has a pitch of 5.

If the chain has a chisel cutter, you will need a flat file. If the chisel cutter has a pitch of 5. The gauges are tools that you use to check the cutter length, top plate angle, and setting the correct depth gauge before filing.

They are available in four main sizes. These are 0. It is recommended that you do not file the depth gauges to below 0. The 0. Filing them lower than that will shorten the service life of the chain. The depth gauges should also be filed evenly throughout the gauge. Failure to do so will cause the chain to vibrate and cut rough, or cut crooked. The gauge measurement is usually displayed on the guide bar of the chainsaw.

It is best to use the displayed value to avoid errors that can occur if you try to measure the gauge size manually. If you cannot find the marking, you can use a pair of calipers to take the gauge measurement. If your chain is completely busted or too worn out, do not keep trying to cut, look here for new chain options. We hope this guide has been helpful and you will have an easy time finding the right chainsaw file size using the chainsaw file size chart.

For more on chainsaw chain sharpening see our guide here. Your email address will not be published. Save my name, email, and website in this browser for the next time I comment. Notify me of follow-up comments by email. Notify me of new posts by email. Chisel Square Tooth, Square Grind The chisel cutter is a highly aggressive cutter, and you should only use it if you are an experienced sawyer. How to Determine File Size for Chainsaw Chain To determine the right file size for your chainsaw, you need to read the number marked on the side of the cutter of the chain.

Measuring the pitch Length between tooth rivets divided by 2.